Day: October 22, 2020

As a common heterocyclic compound, it belong isothiazole compound,3-Bromoisothiazole,55512-82-8,Molecular formula: C3H2BrNS,mainly used in chemical industry, its synthesis route is as follows.,55512-82-8

To a reaction flask were added compound 5 (200 mg, 0.392 mmol), 3-bromoisothiazole (96 mg, 0.588 mmol), Pd(dppf)Cl2 (32 mg, 0.02 mmol) and sodium carbonate (126 mg, 1.18 mmol), 2 mL glycol dimethyl ether and 0.4 mL water were added, bubbled with nitrogen gas for 10 minutes, heated to 120 C in microwave and reacted for 0.5 hour. After TLC detected the reaction was complete, the reaction was concentrated, purified by silica gel column chromatography to afford 84 mg of a product, yield: 46%. LC-MS(APCI): m/z = 467.3(M+1)+; 1H NMR (400 MHz, DMSO) delta 10.17 (s, 1H), 9.04 (s, 1H), 8.90 (s, 1H),8.76 (d, J = 2.3 Hz, 1H), 8.05 (d, J = 2.3 Hz, 1H), 7.86 (d, J = 9.1 Hz, 2H), 7.33 (d, J = 8.8 Hz, 2H), 4.86 (d, J = 3.4 Hz, 1H), 4.21 (s, 1H), 3.41 (dd, J = 17.0, 9.3 Hz, 1H), 3.29 – 3.18 (m, 2H), 2.90 (d, J = 11.1 Hz, 1H), 1.89 – 1.80 (m, 1H), 1.75 (s, 1H).

With the synthetic route has been constantly updated, we look forward to future research findings about 3-Bromoisothiazole,belong isothiazole compound

Reference£º
Patent; Shenzhen Targetrx, Inc.; WANG, Yihan; ZHAO, Jiuyang; AL, Yixin; (51 pag.)EP3553057; (2019); A1;,
Isothiazole – Wikipedia
Isothiazole – ScienceDirect.com

Name is 2,3-Dihydrobenzo[d]isothiazole 1,1-dioxide, as a common heterocyclic compound, it belongs to isothiazole compound, and cas is 936-16-3, its synthesis route is as follows.,936-16-3

General procedure: To the mixture of the precursor 10(2.26 g, 10.1 mmol, 1.5 equiv) and tert-butyl 1,2,5-thiadiazolidine-2-carboxylate 1,1-dioxide (1.50 g, 6.75 mmol, 1.0 equiv) in dry DMF(10 mL), was added Cs2CO3 (6.60 g, 20.25 mmol, 3.0 equiv). Themixture was stirred at room temperature overnight, and thenextracted with ethyl acetate. The organic phase was washed withsaturated NaHCO3 and brine, dried over anhydrous Na2SO4, filteredand concentrated. The resulting residue was purified via silica gelchromatography to give 11a as colorless oil (1.96 g, 79%).

With the complex challenges of chemical substances, we look forward to future research findings about 2,3-Dihydrobenzo[d]isothiazole 1,1-dioxide

Reference£º
Article; Chen, Shulun; Guo, Wei; Liu, Xiaohua; Sun, Pu; Wang, Yi; Ding, Chunyong; Meng, Linghua; Zhang, Ao; European Journal of Medicinal Chemistry; vol. 179; (2019); p. 38 – 55;,
Isothiazole – Wikipedia
Isothiazole – ScienceDirect.com

Name is 3-Chlorobenzo[d]isothiazole, as a common heterocyclic compound, it belongs to isothiazole compound, and cas is 7716-66-7, its synthesis route is as follows.,7716-66-7

A solution of 3-chlorobenzo[d]isothiazole (1.0 g, 5.9 mmol) in chlorosulfonic acid (2 mL) was heated at 150 “C for 2.5h. The resulting reaction mixture was then cooled to room temperature and thionyl chloride (0.9 mL, 12.3 mmol) was added. The resulting yellow solution was heated at 150 “C for 2h, allowed to cool to room temperature and poured over ice. The aqueous reaction mixture was then extracted with ethyl acetate, dried over EPO anhydrous magnesium sulfate, filtered and concentrated under reduced pressure to give a pale yellow oil which crystallized into an off-white solid upon standing at -20 0C (1.43 g). MW=267 confirmed by LC-MS, t,.= 4.17 min (Method B) MH+=268.

With the complex challenges of chemical substances, we look forward to future research findings about 3-Chlorobenzo[d]isothiazole

Reference£º
Patent; RIGEL PHARMACEUTICALS, INC.; WO2006/91858; (2006); A1;,
Isothiazole – Wikipedia
Isothiazole – ScienceDirect.com

Name is Isothiazole, as a common heterocyclic compound, it belongs to isothiazole compound, and cas is 288-16-4, its synthesis route is as follows.,288-16-4

In a pressure-resistant Schlenk tube, copper fluoride (0.05 mmol) was charged,The system was evacuated and replaced with argon three times,Under gas protection,The isothiazole (. 5 mmol) was added sequentially with a micro-injector,Tert-butylperoxybenzoyl (2 mmol),And chlorobenzene (2 ml),The system was then sealed and heated at 130 C in an oil bath for 24 hours,After completion of the reaction, the solvent was distilled off under reduced pressure,The product N-methylisothiazolin-2-one (46 mg) was obtained by a simple column chromatography (eluent using a mixed solvent of petroleum ether (60 to 90 C) and ethyl acetate)The yield was 80%.

With the complex challenges of chemical substances, we look forward to future research findings about Isothiazole

Reference£º
Patent; SUZHOU BOFEITE NEW MATERIALS TECHNOLOGY CO., LTD; Mao, jincheng; Wang, Ping; (7 pag.)CN103965136; (2016); B;,
Isothiazole – Wikipedia
Isothiazole – ScienceDirect.com

As a common heterocyclic compound, it belongs to isothiazole compound, name is 3-Piperazinobenzisothiazole hydrochloride, and cas is 87691-88-1, its synthesis route is as follows.,87691-88-1

EXAMPLE 59; (R)(-)-N-{5-[2-(4-BENZO[D]ISOTHIAZOL-3-YL-PIPERAZIN-1-YL)- ETHYL1-INDAN-2-YLl-ACETAMIDE; A slurry of (R)-N- [5- (2-Chloro-ethyl)-indan-2-yl]-acetamide (2. 00g, 8. 41mmole), Na2CO3(1. 5eq) and 3-Piperazin-1-yl-benzo [d] isothiazole hydrochloride (2. 0eq) in H20 (20moi) was reacted under microwave assistance using a CEM MARS-5 microwave reactor to 175C for 10min. Upon cooling, the reaction was diluted with EtOAc (250moi), H20 (100mol) and the layers separated. The aqueous layer was extracted with EtOAc (2x 50ml). The organics were dried (MgSO4), concentrated, and the residue purified by chromatography (EtOAc) to give (R) (-)-N- {5- [2- (4- Benzo [d] isothiazol-3-yl-piperazin-1-yl)-ethyl]-indan-2-yl}-acetamide (2. 92g, 6. 94mmole) in 100% purity 254 nm; LCMS (APCI) 474 [M+H] +. [a] D25- 3. 6 (c 5.5, CHCl3). 1 H NMR (400 MHz, CHLOROFORM-D) 8 ppm 1.94 (s, 3 H) 2.65-2. 71 (m, 2 H) 2.73-2. 80 (m, 6 H) 2.81-2. 87 (m, 2 H) 3.28 (ddd, J=16. 04,6. 10,5. 92 Hz, 2 H) 3.57-3. 62 (m, 4 H) 4.69-4. 76 (m, 1 H) 5.70 (d, J=7.08 Hz, 1 H) 7.06 (d, J=7.81 Hz, 1 H) 7.11 (s, 1 H) 7.16 (d, J=7.56 Hz, 1 H) 7.35 (ddd, J=8.17, 7.08, 1.10 Hz, 1 H) 7.46 (ddd, J=8.11, 7.02, 1.22 Hz, 1 H) 7.81 (dt, J=8.05, 0.85 Hz, 1 H) 7.91 (dt, J=8.30, 0.98 Hz, 1 H).

With the complex challenges of chemical substances, we look forward to future research findings about 87691-88-1,belong isothiazole compound

Reference£º
Patent; WARNER-LAMBERT COMPANY LLC?; WO2005/56540; (2005); A1;,
Isothiazole – Wikipedia
Isothiazole – ScienceDirect.com

3-Chlorobenzo[d]isothiazole, cas is 7716-66-7, it is a common heterocyclic compound, the isothiazole compound, its synthesis route is as follows.,7716-66-7

PREPARATION 3 3-(1-Piperazinyl)-1,2-benzisothiazole odsold; hydrochloride Anhydrous piperazine (49.4 g, 0.57 mol) and t-butanol (10 mL) were added to a dry, 300 mL round bottom flask equipped with a mechanical stirrer, thermometer, condenser topped with a nitrogen inlet, and pressure-equalizing dropping funnel. After the flask was purged with nitrogen, it was heated to 100¡ã C. in an oil bath. A solution of 3-chloro-1,2-benzisothiazole (19.45 g, 0.11 mol) in t-butanol (10 mL) was added to the addition funnel, and then slowly added to the reaction flask over 20 minutes to moderate an exothermic reaction (112-118¡ã C.). Once addition was complete the yellow solution was heated to reflux (121 ¡ãC.) and then maintained at reflux for 24 hours. Thin-layer chromatography showed that the reaction was complete. The reaction mixture was cooled to 85¡ã C. and 120 mL of water was added. The hazy solution was filtered and the filter cake rinsed with 60 mL of t-butanol/water (1:1) solution. The pH of the combined filtrate and wash was adjusted to 12.2 with 50percent aqueous caustic. The aqueous solution was extracted with toluene (200 mL), the layers were separated, and the aqueous layer was extracted with fresh toluene (100 mL). The combined toluene layers were washed with water (75 mL), and then the toluene solution was concentrated in vacuo at 48¡ã C. to 90 mL. Isopropanol (210 mL) was added to the concentrate and then the pH was slowly adjusted to 3.8 with 7.6 mL of concentrated hydrochloric acid. The resulting slurry was cooled to 0¡ã C., granulated for 45 min, and then filtered. The filter cake was washed with cold isopropanol (50 mL) and then dried in vacuo at 40¡ã C. to afford 23.59 g (80percent yield) of 3-(1-piperazinyl)-1,2-benzisothiazole hydrochloride as an off white solid.

7716-66-7 is used more and more widely, we look forward to future research findings about 3-Chlorobenzo[d]isothiazole

Reference£º
Patent; Pfizer Inc.; US5935960; (1999); A;,
Isothiazole – Wikipedia
Isothiazole – ScienceDirect.com

3-Piperazinobenzisothiazole hydrochloride, cas is 87691-88-1, it is a common heterocyclic compound, the isothiazole compound, its synthesis route is as follows.,87691-88-1

The above intermediate IV (0.01 mol) and the hydrochloride salt of the piperazine compound (V) (0.01 mol) were dissolved in DMF (100 mL), and K2CO3 (0.02 mol) was added.According to the general operation three,Preparation of 3-(4-(3-(6-fluoro-1H-indol-3-yl)propyl)piperazin-1-yl)benzo[d]isothiazole(VI-11) hydrochloride (white solid) 3.44 g, yield 80%.

87691-88-1 is used more and more widely, we look forward to future research findings about 3-Piperazinobenzisothiazole hydrochloride

Reference£º
Patent; Shanghai Pharmaceutical Industry Institute; China Pharmaceutical Industry Zongyuan; Li Jianqi; Gu Zhengsong; Zhou Ainan; Xiao Ying; (26 pag.)CN109467554; (2019); A;,
Isothiazole – Wikipedia
Isothiazole – ScienceDirect.com

936-16-3, 2,3-Dihydrobenzo[d]isothiazole 1,1-dioxide is a isothiazole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,936-16-3

To a mixture of 2,6-dichloropyrazine (193 mg, 1.30 mmol) and 1 (200 mg, 1.18 mmol) in DMF (5 mL), was added Cs2CO3 (770 mg, 2.36 mmol). The resulting mixture was stirred at 100¡ãC for 5 hours. The mixture was cooled to 25¡ãC and poured into ice water. The aqueous phase was extracted with ethyl acetate (20 mL). The combined organic phase was washed with saturated brine (20 mL), dried with anhydrous Na2S04, filtered, and concentrated under reduced pressure. The residue was purified by TLC (petroleum ether/ethyl acetate = 2: 1) to afford 21 (220 mg, 60percent) as yellow solid.

As the paragraph descriping shows that 936-16-3 is playing an increasingly important role.

Reference£º
Patent; NUMERATE, INC.; RAIMUNDO, Brian; KOLTUN, Elena S.; GRIFFIN, John; STANGELAND, Eric; (93 pag.)WO2018/49324; (2018); A1;,
Isothiazole – Wikipedia
Isothiazole – ScienceDirect.com

3-Bromoisothiazole, cas is 55512-82-8, it is a common heterocyclic compound, the isothiazole compound, its synthesis route is as follows.,55512-82-8

Intermediate 123d was reacted with 3-bromoisothiazole in a method analogous to Example 122 to give Example 123 (5.9 mg, 11.5 muiotaetaomicron, 46percent). LC-MS (Method Al) RT = 1.39 min, MS (ESI) m/z: 512.4 (M+H)+. H NMR (500 MHz, DMSO-cfe) delta 9.18 (d, 7=4.6 Hz, 1H), 8.12 (br d, 7=7.9 Hz, 1H), 8.09 – 8.01 (m, 2H), 7.75 (br d, 7=7.9 Hz, 1H), 7.17 (br d, 7=7.9 Hz, 2H), 7.07 (br d, 7=7.9 Hz, 2H), 4.68 (s, 2H), 2.32 (t, 7=7.6 Hz, 2H), 1.90 – 1.77 (m, 6H), 1.67 (br d, 7=6.7 Hz, 2H), 1.49 (quin, 7=7.5 Hz, 2H), 1.27 (dq, 7=14.9, 7.4 Hz, 2H), 0.81 (t, 7=7.3 Hz, 3H) (1 exchangeable proton not observed).

With the rapid development of chemical substances, we look forward to future research findings about 3-Bromoisothiazole

Reference£º
Patent; UNIVERSITE DE MONTREAL; BRISTOL-MYERS SQUIBB COMPANY; PRIESTLEY, Eldon, Scott; REZNIK, Samuel, Kaye; RUEDIGER, Edward, H.; GILLARD, James, R.; HALPERN, Oz, Scott; JIANG, Wen; RICHTER, Jeremy; RUEL, Rejean; TRIPATHY, Sasmita; YANG, Wu; ZHANG, Xiaojun; (642 pag.)WO2018/5591; (2018); A1;,
Isothiazole – Wikipedia
Isothiazole – ScienceDirect.com

As a common heterocyclic compound, it belongs to quinuclidine compound,Quinuclidine-4-carboxylic acid hydrochloride,40117-63-3,Molecular formula: C8H14ClNO328,mainly used in chemical industry, its synthesis route is as follows.,677304-75-5

Step 5; Sulfuryl dichloride (86.7 mg, 728 mumol) is added to a solution of6-bromobenzo[d]-isothiazole-3-carboxylic acid (188 mg, 728 mumol). The reaction mixture is stirred for 30 min before removing the volatiles by rotovap. The residue is taken up in CH2Cl2 (0.587 ml) and a solution of 2-prorhoylamine (62.5 muL, 728 mumol) and triethylamine (101 mul, 728 mumol) in CHjCl2 (1.2 ml) is added. The reaction mixture is stirred at room temperature until LC/MS analysis indicates complete conversion to the desired product. The reaction mixture is diluted with distilled water and ethyl acetate. The layers are separated and the aqueous is extracted with ethyl acetate. The combined organics are washed with brine and dried over Na2SO4, filtered and concentrated to give 6-bromo-N-isopropylbenzo[d]isothiazole- 3-carboxamide.

With the synthetic route has been constantly updated, we look forward to future research findings about 6-Bromobenzo[d]isothiazole-3-carboxylic acid,belong isothiazole compound

Reference£º
Patent; AMGEN INC.; MEMORY PHARMACEUTICALS CORPORATION; WO2007/100880; (2007); A1;,
Isothiazole – Wikipedia
Isothiazole – ScienceDirect.com